4/09/2010

Imperial Valley - The first demonstrations are done!

Hi followers,

the first demonstrations in the Valley are done without any problems and with perfect results. The first demonstration was in the south of Holtville at the first of April early in the morning and the weather became after the first bales really bad. It started to rain, and we had to stop the demonstration for a couple of hours. After Breakfast the sun came back, and so we were able to bale in the afternoon again. The bale weights and the bale shape was pretty well. We had 7 feet bales with 1800 lbs and 12 - 13% moisture. In the afternoon the hay dried very fast, so at the beginning we had also good results, but at the end it was to dry to get really heavy bales. They were heavy enough, but not as heavy as in the morning.




Edit: One more picture of the Hesston baler - but it is the second and last bale, he did, so you also can't compare the bale shape to the Krone bales. But the customer told us, that he can't reach the bale weights we did with the HDP with his Hesston baler and that he liked the shape of the Krone bales very much.
After the first demonstration we had to clean the whole baler with a pressure washer. Normally it works pretty well when we use our leaf blower to blow away all the dust and dirt, but after the rain in the morning there was no chance to remove it only with air. After we searched a little bit in the Holtville area we found this car wash place, which was high enough (11ft) for the JCB (11ft 6 inch). It was also wide enough for the Phiber accumulator.

´
Our second demonstration was in the north of the Valley nearby Brawley with the "four by four" - the BiG Pack 12130 - at a local feedlot. They normally bale with three Hesston balers, but I think, they really liked the performance of the Krone too. We were able to drive roundabout 30% faster and we still had better looking bales. The interested person, we ran the demo for, liked also the EasyFlow PickUp without cam track very much. A really nice constant flow into the machine without any losing of hay amazed him. Also his three operators drove the JCB with the Krone baler, and after a few minutes they made also pretty good bales. He liked it so much, that we were allowed to come back the next day to show also his father our baler on the field.



The next demonstration was in the morning of April 8th north east of Holtville. The customer has several dairys and has to haul his hay over long distances out of the imperial valley. We made some nice heavy 8 feet long bales (average 1800 lbs) with 13-15% moisture, and I think he also liked the Krone baler very much. Another customer in the valley baled for him with an Krone HDP before, and so he also knew a lot about our baler and the nice heavy bales. His demonstration started early in the morning.

The same evening we wanted to demonstrate nearby Westmorland, but it was still to dry in the evening. So we stopped the demonstration at 10 pm and came back today in the morning. At 8.30 am we met at the field, but we had to wait a little bit before we could start again, because it was to wet. At 11 am, we had already done 80 bales, we had to stop again, because now it became to dry. So, the time windows for baling export hay in the valley are very short which makes it not easier to plan aour demonstrations.



We also used my bale scale in the front hitch the first time.


So far for the moment.

Regards Niklas

Reno - Grand Opening!

Hi Followers,

EDIT: Here is an older post of my blog. Somthing went wrong, so it was gone, but here it is again - good, that I saved it on my computer. Sorry for that!



today I want to tell you about the grand opening at Reno office and warehouse last Thursday and Friday. For this important event Bernard Krone, owner of the Krone Group and Wilhelm Voss, member of the management board, from Germany, and also Rusty Fowler, president /CEO of Krone North-America from Memphis office came over to Reno. Thursday evening we had all together a great dinner with many customers and dealers from the western region at the Grand Sierra Resort, and on Friday we had an open house at Reno office and warehouse at

4674 Aircenter Circle
Reno, NV 89502

I think both days were very successful for everybody. Here are some pictures of the open day on Friday.






There was also an offical part on friday - Bernard Krone had to cut the ribbon. Here it was the strong Krone HDP twine, but it was not strong enough for our owner!




But of course it’s a lot of work to prepare such a big event. The whole week before everybody helped to clean up and to arrange everything. Here you can see how the new Krone sign was hanging up just over the front door.


I also had to put all the spare parts into my Roadshow Trailer, and we had to clean all the cars, the Krone Machines, the trailer and the whole floor in the warehouse. But on Thursday noon everything was done.

Here are some pictures of the warehouse I took two weeks ago.


How you can see we are now well prepared for the comming season to send spare parts very quickly to the western region. Because it's very important for our customers to get their machines running again quickly.

So far!

Regards Niklas

3/06/2010

Trip to Imperial Valley

Hi Followers,



I'm back in Reno after a long trip through the south of California. Two weeks ago I went down to Imperial Valley to meet Blake Fuller, a Krone Product Specialist, and Tom Brown, a salesman from Central Implement. Central Implement is the Krone Dealer for the Imperial Valley region. The main reason for that trip was on the one hand to see, where we start our Roadshow at the end of March, and on the other hand to speak to some customers in that region, who still own one or more Krone balers, or who are interested in a Krone baler. For me it was also a very interesting trip, because I had never seen so big fields with vegetables or so many cattle in a dairy before.

Here some salad fields....

... and a big carrot harvester.

Also such a perfect watering system with several canals to get the water from Colorado River to the fields on one side and to drain it on the other side was completely new for me. In Germany we have so much rain, so we don’t need such a system.


It was also very impressive for me to see a big customer like Agritrade, who export the hay, baled with several KRONE BiG Pack HDP, to overseas. Because of the HDP baler they don't have to repress the bales in such a big stationary bale press - the HDP bales are heavy and strong enough to load a container to its maximum weight. So it is possible to load the containers directly on the field - that saves lots of money.



Another very interesting place was at Triple III Press, where they repress small bales with big stationary presses to get higher Bale density, so that they can load a container up to the weight limit. They also cut the bales into two pieces for the asian market, because the smaller bales are easier to handle over there. Many people buy every day the hay they have to feed to their cattle, and they have to carry it home by small vehicles or motor-scooter.

Here you can see the huge hay and straw storage, and some of the Containers they have to load.

This is the place, where the normal bales come to the machine. A forklift pushes a hole pack into this red frame....

..... so that the bales could be lined up on the other side to a transport belt which carries them to the press.

On the way to the main part of the machine an operator removes the twine of the small bales, so that the blue hydraulik driven bar can push the material into the press chamber of the stationary baler press.

Here you see the other side of the machine. On the right side you can see the hydraulik driven plunger, and on the left side in the front you see the new high density bales, which are ready for shipping. You can also see, that they are cut into two pieces, to make the bales smaller. 

And here they load the plastic wrapped bales into one of the containers.

Every day in the morning we could see the Blue Angels, the U.S. Navy's flight operation squadron over the valley, when they were on their training flights. It was amazing to see them operating in the blue sky.





So, the week at the Imperial Valley was very interesting for me, because I saw many interesting things, and of course we had some good customer meetings too. But the most important aspect for me is, that I know, where I will start the Big Krone BiG Pack 1290 HDP Roadshow 2010 at the end of the month. Now I know a little bit of what's going on down there.

Regards
Niklas


2/18/2010

Trip to Smith Valley

Hello,
Tuesday morning Brent and me made an excursion to the "Smith Valley" south east of Carson City


We had to pick up two spare tires for the Big Pack I have to carry with me in my trailer. I hope I will never have to use them, but it’s better to have them for such a long journey.

I also used the chance to meet our local dealer at the smith valley and to talk to him about the roadshow. I was very surprised, that he still hat so much interested customers jet. He also told me a lot about the region. But he also thought that we couldn’t start baling before May. So I think, I will be back the in May.

n the following pictures you can see some impressions of the region and the way out there. The landscape is very different to the landscape when going eastwards to California. Here it is dryer, and it looks more like the desert. I don’t know why, but when I see this kind of landscape I will be remembered to one of my favourite movies named “Convoy” with Chris Kristofferson.
I looked out the whole time for that nice black Mack with this small rubber duck on the hood.


In the valley there is a complete different landscape again. You could see farmland and cattle, and everything is a little bit “greener” than the Tumbleweed and bushes along the Highway before.


Here you can see the nice bright colours of the Krone products in front of the pale looking mountains with a little bit of snow.
Here you can see our dealer in the Smith Valley Area.

It is also very interesting for me to see such a typical dealer outside the big cities and of course not in Germany. There were many interesting machines standing outside the shop, some of them I've never seen before.

New and old, unused and used are standing side by side. Some of them will never go to work again, but they are still used to get spare parts. In the shop you can find everything you need, and it's also possible to by single parts like bolts or nuts. It was a very interesting trip for me, and I’m looking forward to come back to demonstrate our HDP baler here.
On the way back we just bought some stuff for the trailer, so that I can complete it this week too. I have to attach some cabinets for tools and spare parts. We also decided to put some linoleum onto the floor so that it is easier to clean it, even when grease or oil comes onto the floor. So I have enough work to do this week.

Regards Niklas
At least a photo I have made this morning. I think, it looked fantastic, when the sun comes over the mountains every minute.